Status: design settled; the Rev A schematic is complete and every decision is made — the board is ready for PCB floorplan and routing. Every net is drawn, every part has a footprint, and the switch is solid state (the case has no height for a relay): an NC7SB3157P6X 2:1 switch on DS-A, a TPS22918 on the Gotek’s +5 V and an AO3400A on its ground return, with the same fail-safe as before — the switch’s own truth table puts the physical drive on the S-low throw. The panel switch is a plain SPST flip switch on a 2-wire lead to a bare 2-pin header. Tracks #62, and the floppy interposer personality #20. Source: hardware/floppy-adapter/, docs/floppy-adapter-design.md. Board register: hardware/README.md.

This board’s own Rev A / Rev B are unrelated to the interposer’s Rev A / Rev B — the letters always carry the board’s name.

What it is

A small daughter card that lets you choose, from a front-panel switch, whether the drive A position is served by the physical drive or by a Gotek (FlashFloppy) emulator — with drive B always present in both modes.

It sits between the Osborne 1’s floppy header and the OEM floppy cable. Nothing in the machine and nothing in the cable is cut.

Why it is not just a cable

Two prior designs exist, and this one deliberately improves on both:

  • Wayne Visser’s adapter is a passive tap — it puts a Gotek on the bus alongside the physical drives and switches nothing. Its pin and rail mapping is kept as the interface reference.
  • Richard Loxley’s hand-wired build proved the concept but needed a DPDT switch and a 5 V relay soldered onto the Gotek, plus hand-cut Dupont cable. This design moves all of that onto a PCB at the connector end.

The interface, and the mistake worth recording

The machine uses a Shugart-like 34-pin interface, but with +5 V and +12 V routed to the drives over otherwise-unused cable pins — there are no separate drive power connectors, which is why the card has to tap the cable rather than add a supply.

The pinout was first transcribed from the archived Visser adapter, then re-read from the Osborne 1’s own schematic (DWG 1A2011-00 Rev E, sheet 9 of 9, the P8 symbol). That second reading corrected two pins and a ground row — and one of the corrections is the reason this card can exist at all:

Pins 4 and 6 are not ground. They carry live FDC outputs — TG43 and EARLY. The earlier transcription tied pins 2, 4, 6 and 7 to GND, which is harmless on a Gotek-only adapter, but this card switches the OEM cable through to real drives, and clamping TG43 low would assert reduced write current permanently. The card passes 4 and 6 straight through instead.

That is a good example of why the project re-reads primary sources rather than trusting a prior adapter’s transcription.

Still to do

  • PCB floorplan and routing — this is the next unit of work. Every decision is made, every net is drawn and every part has a footprint.
  • Height is the binding constraint and the floorplan must respect it: it is why the switch is silicon, and the three packages are ~1.5 mm against a relay’s 10 mm.
  • Getting the cables out of the pocket, two accepted routes: break the 34-pin run into parts that pass the ventilation slots (Loxley’s approach — nothing on the machine is cut), or cut the case for a full-size 34-pin cable alongside the two switch wires. The card is the same either way, which is why J3 is a full 2×17 header.
  • The front-panel switch, which is also the point at which this card and the control pod have to agree on a physical interface. It is a plain SPST flip switch: up = the physical drives, down = the Gotek, on a 2-wire twisted-pair lead with a series resistor — up is the fail-safe position, because open leaves the control node pulled low.