interposer-upgrade
O1NEXT Upgrade — the core board and its panel, one board in four snap-off sections
Status: the interposer’s Rev A engineering-sample schematic generated, ready
for KiCad capture review and routing. Rev B is a pin map with no schematic yet
(#259). No board built.
Tracks #11 (Phase 1), #12 (interface spec), #83 (ROM 2.00), #259
(one board — it absorbs #13 and #15), #297, #303, #304, and #14 (the pod).
Source: hardware/interposer-upgrade/. Board register:
hardware/README.md.
One board, four snap-off sections
This is one delivery in four parts — and the parts are sections of one PCB,
routed and separated by mouse bites, so the panel is completed in one pass,
with every surface-mount part landing at once and a single board-handling
requirement: the interposer board itself (Rev 0 → Rev A → Rev B), the
UI pod below, the ROM socket tap (the UD11 daughterboard the Pico serves the
window through) and the character ROM socket tap (UA15). They have notes rather
than schematics of their own; only the interposer’s schematic exists.
The ROM taps are air connected. Snapped off, a tap sits in the machine’s own ROM socket, nowhere near the Z80, so its nets leave the PCB and come back through a pair of header pin assemblies wired back-to-back.
What it is
The centrepiece: a board that sits between the Z80 and its socket, carrying a RP2354B. Because it sees every bus cycle, it can both observe the machine and drive it — which is what makes the whole “virtual peripheral” idea possible.
It is also the precursor of the O1NEXT Integrated board: the SFF designs the same capability in as firmware instead of stacking it on, so the SFF can replace the interposer and the interposer cannot replace the SFF. And it can act as any one of the three standalone boards — the USB Keyboard Adapter, the WiFi COMM PAC and the Drive C Repro — so if you have it you don’t need them.
What it hosts
Nine personalities, each with its own page of research behind it: the passive bus analyzer (#17), the RT-60A time service (#18), the virtual MX-80 printer (#19), the floppy interposer (#20), the WiFi modem (#21), Drive C (#22), the virtual CoPower-88 (#23), the SCREEN-PAC video personality (#24) and the web KVM console (#45).
How it attaches
- Z80 DIP-40 socket — socket-safe header, 4 MHz bus sampled synchronously via PIO.
- 74AHCT/HCT both directions. All Osborne 1s are NMOS Z80s, so AHCT/HCT matches the NMOS I/O thresholds; this superseded an earlier 74LVC245 choice.
- Its own dedicated 5 V feed near the Z80 socket, sized for RP2354B WiFi bursts (~300 mA+).
- It must stack. The design has to coexist with a real SCREEN-PAC and a real CoPower-88 on a fully-loaded machine, so pass-through height matters.
- An optional second tap: the 24-pin character-generator socket (UA15), for
the video personality. Read-only by necessity — the ROM’s
/CEand/OEare grounded on the mainboard, so it is always driving.
One board, three revisions
The interposer is one board: Rev 0 → Rev A → Rev B. Rev B is the
production revision, not a second product — the split #13 and #15 described is
what #259 collapsed, and Rev B keeps everything Rev A had.
- Rev 0 “test probe” — superseded. Kept for the decision record; parts lead time for a passive probe was within days of an engineering sample of the active board, so the passive step was skipped.
- Rev A engineering sample — the instrument. An SMT Z84C00 on the board (pull the original CPU, drop the interposer in), /BUSRQ bus mastering, a 595/165 shift-register drive-and-capture fabric, the bare RP2354B plus a castellated ESP32-C3, and W25Q library flash. The goal is blunt: the development partner controls the hardware — memory read/write, ROM dumping, code injection and execute. The board is SMD — the Z80 socket is through-hole, not the board.
- Rev B — the production revision, and the one that gets built. It keeps
the whole Rev A instrument —
/BUSRQmastering and the 595/165 fabric — and adds the live-cycle personality engine: a 74AHCT688 window comparator plus /WAIT cycle stretching, the period-correct slow-peripheral mechanism, which replaces 16 direct address lines with two. HSTX is fixed to GP12–19, so HDMI lives there; the status LED bank moves to the ESP32; SD goes on SPI. Rev B has no schematic yet — #259 is the issue that produces it.
The control pod
A ribbon cable to the front-panel pod (hardware/interposer-upgrade/ui-pod/) carries
SD/USB storage, HDMI out, an OLED, FlashFloppy-style controls, a modem LED
bank, and a second-keyboard USB-A path. The pod is part of this board, not a
board of its own.
Onboard storage
The interposer carries enough flash to hold a built-in library — at minimum the boot diskette — so the machine is useful with no card inserted, and the O1NEXT can boot “factory” images out of the box. A DD diskette image is about 400 KB, so a handful of SOIC-8 W25Q-class parts is effectively free.