Status: concept render exists. Tracks #49 and #52 (Phase 5), plus #125 (the Osborne 3 history) and #128 (the specification). Source: hardware/next-integrated/ (the board inside it), docs/design/. Board register: hardware/README.md.

It is hardware, but it is not a board. O1NEXT Complete is the next-integrated board with the rest of the machine wrapped around it — chassis CAD, print STLs and an assembly BOM, plus the machine’s own keyboard PCB. It has its own folder (hardware/o1next-complete/) and page, and no schematic of its own because it is CAD and a BOM, not a PCB.

What it is made of

Piece Where it stands
Chassis CAD the render and outline, docs/design/o1next-lunchbox-concept.* (#53)
Print STLs the printable chassis and keyboard-mounting parts, to produce (#52)
Assembly BOM board, 8” panel, 18650 pack, keyboard, fasteners — to produce (#52)
The board inside it next-integrated

The machine’s keyboard is incidental to the design, not a board of its own: a custom USB keyboard — QMK-compatible, Cherry MX, in the Osborne 1 layout — so the machine keeps the O1’s layout, keycaps and “keyboard seals the unit” geometry. It shares its 8×8 matrix work with the USB keyboard interface (#47), and it is part of this machine’s CAD work (#52) rather than a folder of its own.

What it is

The end of the road: a complete, modern-parts Osborne 1 that runs original ROMs and original software, in a case — not a board, not an upgrade, a machine.

The O1NEXT is the SFF board with the rest of the machine wrapped around it. The logical equivalent of the C64 Ultimate “Crystal” edition: an homage that gives the end user everything that would have been possible in the olden days, wrapped in a way that makes it awesome. The machine that was an absolute fantasy in 1985 and is do-able by a hobbyist today.

The board inside it

One board, and it is the whole foundation:

Board What it is
next-integrated A fully integrated board: the interposer’s personalities designed in as firmware. Not a 1:1 swap, and it does not try to be — it can go in a real chassis or into any other design, up to the end user

A 1:1 replacement for an OCC1/OCC1A mainboard — the restoration path — is possible if a chassis ever needs restoring, but it is not planned and not built (2026-10-19), and it has no page here. See Hardware that is not a board in hardware/README.md.

The board shares the USB-C PD power architecture with the machine, including the optional 4S 18650 path.

The machine

About 8 cm thick, in the Osborne 1A’s own blue-and-grey industrial design: an 8” 1024×768 HDMI panel, a keyboard that forms the front cover, and modern power.

The design constraints

  • The keypad is dropped. It duplicates the number row — two switches on the same matrix connections — so it earns nothing and costs space.
  • Under 250 mm wide, so the major parts fit the most common 3D-printer bed.
  • USB-C PD, with an optional 18650 battery path. The same power board serves both boards.
  • The display is settled: HDMI. An 8” 1024×768 panel inside and an external HDMI port — the RP2354B drives it directly, and those panels are readily available. The next-integrated board carries no composite driver circuitry at all, so the discrete analogue chain an OEM mainboard has is simply not here.

The reference designs

Not invented — borrowed from the machines that did the same job:

  • Compaq Portable III — the canonical lunchbox: keyboard as the front cover, a pop-up flat display, and a rear expansion unit.
  • Dolch PAC — the ruggedised industrial lunchbox: handle on top, flat panel front, expansion inside.
  • Osborne 1A — the aesthetic target, and the whole point: grey ABS, blue accent stripe, blue branding, and a keyboard that docks to seal the front.

The Osborne 3

The O1NEXT is the Osborne 3 that should have been — the machine the line was heading for, built with the openness the real Osborne 3 never had.

The name is real. The Osborne 3 was the last computer Osborne Computer Corporation shipped — announced October 1984, on sale spring 1985, $2,995 — and the only IBM-compatible they ever built. It is also the machine where Osborne stopped being Osborne:

  • It was not their design. Licensed from Morrow Designs and almost identical to the Morrow Pivot, so it wore Morrow’s industrial design rather than the Osborne 1’s blue-and-grey.
  • It abandoned their software — MS-DOS 2.11, not CP/M.
  • Its screen was the known failure. Price forced a 16-line display instead of 25, and like all early non-backlit LCDs it was “difficult to read without perfect lighting”. One owner reports wearing a miner’s headlamp to use it.
  • Nothing adjusted. “Neither the screen or keyboard position is adjustable.”
  • OCC went bankrupt again in early 1986; the assets were sold, and no schematics were ever published.

That is the counter-example to the whole project. The Osborne 1 is open and documented, which is why it is still reproducible forty years on. The Osborne 3 was a licensed rebadge, and it died with its vendor.

So the O1NEXT is the Osborne 3 OCC should have built. Four design commitments (the full specification is #128):

  1. Retain the OCC aesthetic rather than dark grey. Grey ABS, blue accent stripe, blue branding: the Osborne 1A’s language, not the rebadged box the real Osborne 3 shipped in.
  2. A usable screen. A panel you can read in a normally-lit room — 80×25, not the 16-line compromise, and backlit.
  3. A detachable keyboard. It docks over the front and seals the unit, as the Osborne 1’s does. Nothing about the machine’s ergonomics is fixed by a hinge.
  4. Open and reproducible. Schematics, firmware and case files published, so anyone can build one. The opposite of a licensed rebadge.

It shares the USB-C PD power architecture with the SFF board it is built on, and sits downstream of #49 (the reproduction) and #52 (case and power).

(The Osborne 3 history above comes from its entry at oldcomputers.net and the Osborne Computer Corporation article on Wikipedia; both agree on the Morrow licensing and the 16-line display.)

Deliverables

  • A power board spec — USB-C PD trigger, 5 V and 12 V regulators, and the optional 4S battery path.
  • An O1NEXT concept design and renders, with enclosure dimensions, the LCD and keyboard selection, and a print-feasibility check against the 250 mm limit.
  • An Osborne 3 design brief — the four commitments above, plus the panel and keyboard selection and the publishing route for the schematics and case files.

Depends on

  • #49 — the reproduction this encloses.
  • #24 / #44 — the video personality and the character ROM. The output is settled (HDMI); the personality itself is still #24’s work.
  • #47 — the O1NEXT’s keyboard is a Cherry-MX implementation of the same matrix, so the USB keyboard interface and the built-in keyboard share their work.
  • #125 — the Osborne 3: the four commitments above, and the open-publishing plan.